View previous topic :: View next topic |
Author |
Message |
SHEEL tinkerer
Joined: 02 Dec 2002 Posts: 140 Location: Melbourne
|
Posted: Fri May 02, 2003 6:22 pm Post subject: Elec Dizzy |
|
|
N E One Know what the 2 wires are coming off the rodeo g200 electronic dizzy? suggestions as to wiring it to the standard gem loom would be helpful.
Sheel out. _________________
|
|
Back to top |
|
|
Wagonslut tinkerer
Joined: 11 Apr 2002 Posts: 376
|
Posted: Fri May 02, 2003 6:29 pm Post subject: Re: Elec Dizzy |
|
|
two of those wires go to a resistor type thing(cant remember the proper name). u buy them from supercheap/autobarn/repco. u need this part for the dizzy to work! |
|
Back to top |
|
|
SHEEL tinkerer
Joined: 02 Dec 2002 Posts: 140 Location: Melbourne
|
Posted: Fri May 02, 2003 6:47 pm Post subject: Re: Elec Dizzy |
|
|
thats not the balace resistor is it? _________________
|
|
Back to top |
|
|
pig75 tinkerer
Joined: 11 Jan 2003 Posts: 72
|
Posted: Fri May 02, 2003 9:42 pm Post subject: Re: Elec Dizzy |
|
|
if its a proper electronic dizzy you will need a ignition module these can be found on a holden shuttle.you can also use one off a valiant or a sigma. the shuttle one is the easiest one to fit it sits on top of the coil |
|
Back to top |
|
|
Wagonslut tinkerer
Joined: 11 Apr 2002 Posts: 376
|
Posted: Sat May 03, 2003 12:59 pm Post subject: Re: Elec Dizzy |
|
|
Thats it! ignition module. buy it from repco, they have 4 wires coming off it, 2 two the dizzy and the other 2 go to the coil! |
|
Back to top |
|
|
Loz backyard mechanic
Joined: 05 Oct 2001 Posts: 943
|
Posted: Sat May 03, 2003 3:06 pm Post subject: Re: Elec Dizzy |
|
|
Depending which dizzy it is they will either go to a control module or to neative and positive of the coil. You shouldnt need to run a balast resistor with electronic ignition if you have the right coil.
Loz |
|
Back to top |
|
|
GeminiCoupe tinkerer
Joined: 10 Jan 2003 Posts: 172
|
Posted: Sat May 03, 2003 5:43 pm Post subject: Re: Elec Dizzy |
|
|
would the dizzy off the G200 fit a G160 and what would u need to fuck around with to get them in? Ive had enough of fukn around with points
GeminiCoupe- |
|
Back to top |
|
|
Wagonslut tinkerer
Joined: 11 Apr 2002 Posts: 376
|
Posted: Sat May 03, 2003 5:49 pm Post subject: Re: Elec Dizzy |
|
|
itll fit, u just need the dizzy itself and an ignition module! |
|
Back to top |
|
|
Gem_A9R tinkerer
Joined: 13 Mar 2003 Posts: 78
|
Posted: Sun May 04, 2003 1:46 pm Post subject: Re: Elec Dizzy |
|
|
Ya dizzy sounds like Mine. Does it have a 2 Black Boxs in side the the Dizzy itself(Around the Rotor Button Shaft)?
If so, Ya don't need a Ignitor Box. The 2 wires connect to:
1 wire goes to Negative(-) on ya Coil and the other goes on the Ballast Resistor. When say on the Ballast Resistor, Ya need to Bypass the Resistor entirely. Goes the Dizzy needs 12 volts all the time, That Ballast resistor drops the Voltage to 8 volts(Stand Points for Gemis).
Try that, If it wont start than swap the wires around and it should sweet. Than after that, BUY A PROPER ELECTRONIC IGNITION COIL, Because you will blow up a GT40R or Standard Gemini on because they're 8 volts not 12volt.
And set ya timing to 10 degree BTDC.
If ya any problems E-mail me and I'll give ya my Mobile Number. I'm in Melbourne and Glad to help. |
|
Back to top |
|
|
|