Parts 4 sale - qld.

Mark · tinkerer Joined: 04 Oct 2001 Posts: 153

Im just about to turbo my race gem. As such have some stuff i want to get rid of.
1. Flowed reco 350 holley on a ported manifold witha 3 inch riser under the carby and a 3 inch tall k+n 9inch round aircleaner. This sticks the air cleaner about 2 inches thru the bonnet. - $300 for the lot.
2. a big crow cam - has 497 thou lift, 302 degree duration and 112 degree lobe separation. Is suitable for nitros or atmo motors ( not turbo ). Reqs heavy springs and flycuts to run. Cost $230 , < 3 months old, sell $150 and can help install.
3.a set of pace maker 4 into 1 extractors. 1 1/2 inch primaries, 2 1/2 inch collector. cost $230, < 3 months old, sell $150.
4. A rebuilt 2litre motor, 60 thou over, hypertectic pistons, heavy duty single row chain, high volume oil pump, arp rod bolts and main bolts, balanced and blue printed, ported 1600 head, big valves, 30/70ish cam, head and sump off for inspection. $500

Adam · Site Admin Joined: 04 Oct 2001 Posts: 682

Hmm, mark that 2 litre is very tempting... I mean, for the hassle of building my motor.... damn you, now it is more dificult again... the decisions... hmm, what condition is it in? how comprehensively ported is the bottom end? How many k's.. how many of them were in a straight line for 400 metres at a time?

Mark · tinkerer Joined: 04 Oct 2001 Posts: 153

Not sure on how many kms, it came included with heaps of stuff i bought. I was told it had been fully rebuilt ($3000) receipts 40,000km ago, but cannot prove either way. Pistons and oil pump still look new as do all the bottom end bolts, and there is still crosshatching in the bores, so I guess it hasnt done too many kms. Ummmmm you dont normally port the bottom end though. The head is only mild, has large valves, slight machine and port and a mild 30/70 cam. Cant really tell you any more than that.

Adam · Site Admin Joined: 04 Oct 2001 Posts: 682

er, typo on the porting... lol...

Hmm, Damnit, I've got my g200 sitting in the workshop in redcliffe, it only needs a hone, rings, bearings and a cam... but your one sounds nice... aargh... I'll have to think about it...

matey_mate · tinkerer Joined: 23 Oct 2001 Posts: 165

does the 2 litre have a carby on it? where abouts are you?

sime · tinkerer Joined: 27 Oct 2001 Posts: 352

how much would it cost to send the engine to melbourne?

cheers

simon m

Andrew65 · tinkerer Joined: 23 Feb 2002 Posts: 303

Is the 2lt the same one that was in the coupe a couple of weeks ago when I drove it?

Gold TX Sleeper · backyard mechanic Joined: 05 Feb 2002 Posts: 509

Would you consider being paid for the engine over 2 or three weeks ? Obviously i'll keep paying for the three weeks, and get the receipts off you, then pick up the motor once it's paid in full.
Jasyn...
P.S What compression is it running ? Is it drivable on leaded and or Optimax ?

matey_mate · tinkerer Joined: 23 Oct 2001 Posts: 165

hey mark how bout if i pay u CASH on the spot for your motor, and maybe the carby to and take it off your hands... ph:0438145310

Mark · tinkerer Joined: 04 Oct 2001 Posts: 153

No carby, but can give you standard manifold and carby with it if you want, or for the extra dollars give you a 350 holley on manifold etc.